CAN I SET UP A BATHTUB MYSELF? FACTORS TO CONSIDER AS WELL AS ACTIONS

Can I Set Up a Bathtub Myself? Factors to Consider As Well As Actions

Can I Set Up a Bathtub Myself? Factors to Consider As Well As Actions

Blog Article

Book Your Installation

We've noticed the article involving Tools You Need to Install a New Bathtub down the page on the internet and decided it made perfect sense to talk about it with you here.


Installing A Bathtub
Installing a bath tub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is likewise a moderately tough project. If the old bathtub is easily obtainable, the job can move immediately; if you have to open up a wall to get rid of the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and embeded in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a contractor to take over a halfway-completed task, it is much better to take into consideration employing one before you start. Chances are you might require a professional plumber to make tube connections.
This write-up will assist you mount a new bath tub in your bathroom if you have actually currently purchased a brand-new bathtub and do not require to change the setup of your previous water supply pipes.
Your devices and product list ought to consist of the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Planning for the Installation


    First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps unit to avoid stress on the tub.
    Fit the adaptable tap adapters to the bottom of both taps using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the supplied washers.
    Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its last placement.

    Removing Old Touches


    If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, activate the faucets to drain any water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is often the case.
    Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the staying water that will come from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
    Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

    Setting up the Bathtub


    Utilizing the two wood boards under its feet, place the bath tub in the needed position. The wooden boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small points.
    The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bathtub till the level reads level.
    To mount faucets, fit the bottom of the furthest versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
    Switch on the water supply and also examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub as well as likewise check the overflow electrical outlet and the normal outlet for leaks.
    Finally, repair the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has been made use of at the very least when as this will certainly settle it into its final position.

    Suitable New Taps


    If the tails of the new faucets are plastic, after that you will certainly require a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
    If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location in between the faucet as well as the sink. Safeguard the faucet in position with the producer offered backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous type ought to be connected to the tap ends first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bath tub


    In the location where the bath satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture an inflexible seal, causing the water to penetrate the wall surface in between the bathroom as well as the tiling, resulting in complications with dampness and also possible leaks to the ceiling listed below.
    You can pick from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealant can fracture relatively early if you do not take into account this activity prior to sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I'm certainly very inquisitive about A Step-by-Step Guide to Installing a Bathtub and I hope you appreciated the new post. Sharing is nice. One never knows, you may just be helping someone out. We take joy in reading our article about How to Install a Bathtub Yourself.




    Schedule Your Service


    Report this page